Bath Brushes, Sponges

Gum bichromate is a 19th century photographic printing process based on the light sensitivity of dichromates. It is capable of rendering painterly images from photographic negatives. more...

Home
Bath & Body
Antiperspirant, Deodorant
Bath Bombs, Fizzies
Bath Brushes, Sponges
Bath Oil
Bath Salts
Bath Sets, Kits
Body Lotion
Body Powder
Body Scrubs
Body Sprays, Mists
Body Wash, Shower Gel
Bubble Bath
Cellulite Treatment
Foot Treatment
Mixed Items
Other Items
Samples, Travel Sizes
Scar, Stretch Mark Reducers
Soap
Dietary Supplements,...
Hair Care
Hair Removal
Health Care
Makeup
Massage
Medical, Special Needs
Nail
Natural Therapies
Oral Care
Skin Care
Vision Care

Gum printing is traditionally a multi-layered printing process, but satisfactory results may be obtained from a single pass. Any color can be used for gum printing, so natural-color photographs are also possible by using this technique in layers.

More on gum bichromate

An overview of gum printing history and process

Gum bichromate, or gum dichromate as it is also known, is a photographic printing process invented in the early days of photography when, in 1839, Mungo Ponton discovered that dichromates are light sensitive. William Henry Fox Talbot later found that colloids such as gelatin and gum arabic became insoluble in water after exposure to light. Alphonse Poitevin added carbon pigment to the colloids in 1855, creating the first carbon print. In 1858, John Pouncy used colored pigment with gum arabic to create the first color images.

Gum prints tend to be multi-layered images sometimes combined with other alternative process printing methods such as cyanotype and platinotype. A heavy weight cotton watercolor or printmaking paper that can withstand repeated and extended soakings is best. Each layer of pigment is individually coated, registered, exposed and washed. Separation negatives of cyan, magenta, and yellow or red, green, and blue are used for a full-color image. Some photographers prefer substituting the cyan emulsion in the CMYK separations with a cyanotype layer. A simple duotone separation combining orange watercolor pigment and a cyanotype can yield .

Low density photographic negatives of the same size as the final image are used for exposing the print. No enlarger is used, but instead, a contact printing frame or vacuum exposure frame is used with an ultraviolet light source such as a mercury vapor lamp, a common fluorescent black light, or the sun. The negative is sandwiched between the prepared paper and a sheet of glass in registration with previous passes.

The print is then floated face down in a bath of room-temperature water to allow the soluble gum, excess dichromate, and pigment to wash away. Several changes of water bath are necessary to clear the print. Afterwards, the print is hung to dry. When all layers are complete and dry, a clearing bath of sodium metabisulfite is used to extract any remaining dichromate so the print will be archival.

Darkroom technique

Materials and equipment

Sheets of good quality 100% rag (cotton) white or bright hotpress watercolor paper (i.e. Arches Aquarelle, Fabriano Artistico); Gum arabic or pre-mixed (pre-mixed solution recommended); Water color pigment in powder or (tube colors recommended); Ammonium, sodium, or potassium dichromate crystals (potassium dichromate recommended) NOTE: Read the MSDS thoroughly before handling.; Gelatin; Chrome Alum; Potassium metabisulfite; for dichromate solution (Part B, Recipe II below); for each color/gum solution (Part A, Recipe II below); or ; Sponge brush for applying emulsion; Camel hair brush and/or paint brush to give brush marks; Sun, metal halide ultraviolet light source, or ; Developing tray & tongs; ; ; Clothes line and pins for drying; Pushpins; Adhesive tape; ; Waxed paper; ;

Read more at Wikipedia.org